Why Is My Anker Soundcore 2 Speaker Not Working And Keep Disconnecting?

In this article, you will learn everything that has to do with why your Anker Soundcore 2 Speaker keeps disconnecting/not working and how to fix them so keep reading…

Why Does My Anker Soundcore 2 Speaker keeps Disconnecting?

Your Anker Soundcore 2 Speaker keeps disconnecting because either your battery is faulty or the distance between your audio source and the speaker are too far from each other.

Possible Reasons Why Your Anker Soundcore 2 Speaker Keeps Disconnecting

  1. Connection is unstable
  2. The speaker is not charged
  3. Faulty battery
  4. The speaker can’t connect with the audio source
  5. Uninstalled software updates
  6. Electronic Interference

1. Unstable Connection – The speaker most definitely not be able to maintain a stable and strong connection with the paired device. What you need to do at this point will be to let only the device in use stay connected to the speaker while other devices stay disconnected.
2. The speaker is not charged – A single charging session of an Anker Soundcore 2 can take as long as 15 hours to be fully charged. Once the battery is getting low, you should receive a notification on the low battery status. It should be charged as soon as possible.


How To Fix Laptop Volume That Keeps Muting


3. Faulty Battery – The battery of the speaker has expiry and sometimes it could last for 5 or more years and knowing this is very vital to you purchasing the speaker so you need to make inquiries on this before making your purchase. Note that some of these sort of devices stop working after the expiry date of their battery so you should know in order to replace it on time.

4. The speaker can’t connect with the audio source – This usually happen when the speaker was hitherto connected to another device and the said device is still connection enabled. This is bound to cause some issues with the connection and pairing with other audio sources.

CHECK OUT:  Are Smart Plugs Good or Bad for Electronics?

5. Uninstalled software updatesLaptops and smartphones should be updated at regular intervals. You should already be receiving notifications from the manufacturer routinely and should act upon receiving such update notice. This is because there is bound to be some issues with the performance once your device is not up-to-date.

6. Electronic Interference – Other devices mostly those electronics with 2.4GHz frequency that are in proximity with the speaker can obstruct it from pairing. What you need to do at this point is to turn off other electronic devices or better still change your location. Plug put devices that are peripheral if they are in use.

Why Does My Anker Soundcore 2 Keeps Cutting Out?

Your Anker Soundcore 2 keeps cutting out because either the circuit board is broken or the speaker is faulty.


How To Fix A Very Slow 5G Speed Connection


Most times, there are wear and tear that are done internally and you may not notice because it is not external. This is a serious issue and is probably the reason you are experiencing those cutting at intervals.

Why Is My Anker Soundcore 2 Skipping Audio?

Your Anker Soundcore 2 keeps skipping audio because your device that should produce the audio and your speaker are not close to each other and thereby causing your audio to skip at intervals. Another possible reason for this issue could be that the audio source you are using is not compatible with your speaker.

Sadly, the issue of incompatibility do not have any solution as it states clearly that the speaker of a certain brand does not support the device so you should consider buying another speaker that supports the device.

How To Fix Anker Soundcore 2 Speaker That Keeps Disconnecting

There are diverse ways to get this issue fixed and you can reset your speaker, bring the two connecting devices close or charge the speaker.

How To Reset Your Anker Soundcore 2 Speaker

  • Click on the Bluetooth button and hold for about 9 seconds then release the button
  • Click on the power button and hold for at least 9 seconds then release it
  • Switch on the speaker

How To Reduce The Distance Between The Device And Your Speaker

  • Shift your speaker nearer to your WiFi
  • Remain close to where your WiFi is
  • Turn your router off and on it again (this is to let you examine if your router is still working)
    Connect your device

How To Charge Your Anker Soundcore 2 Speaker

  • Turn your Anker Soundcore 2 Speaker off
  • Plug the speaker into a nearby power outlet
  • Give it time to charge

N/B:
At 5V2A, your Anker Soundcore 2 Speaker takes about 4 to 5 hours to charge fully.

CHECK OUT:  Is 512GB SSD Enough For A Laptop and Gaming?

Why Does My Anker Soundcore 2 Speaker Keeps Turning Off?

Your Anker Soundcore 2 Speaker keeps turning off because you left it unconnected for about 10 minutes. The turning off is automatic and it will sure turn off once it is left unconnected for about 10 minutes.

Note that if you have connected the speaker to a device but it keeps turning off regardless then it means the battery is low and you should get it charged.


Is 512GB SSD Enough For A Laptop and Gaming?


Why Does My Anker Soundcore 2 Speaker Keeps Disconnecting From WiFi?

Your Anker Soundcore 2 Speaker keeps disconnecting from WiFi is because of thick walls or your connection is poor/weak. If the WiFi is in a different room from where your speaker is then it becomes difficult for a smooth connection and bound to be issue.

To fix this problem follow the steps below:

Move your Anker Soundcore 2 Speaker nearer to the WiFi and stay close to the WiFi router.

Why Does My Anker Soundcore 2 Speaker Keeps Disconnecting From Bluetooth?

Your Anker Soundcore 2 Speaker keeps disconnecting from your Bluetooth because the laptop/device have some issues.

You can fix it by power-cycling your laptop/device.

  • Firstly, switch off your laptop
  • Pull out the battery
  • Click and hold the power button for at least 30 seconds
  • Fix back the battery
  • Switch the laptop back on

Why Is My Anker Soundcore 2 Speaker Making A Buzzing Noise?

Your Anker Soundcore 2 Speaker is making a Buzzing Noise because either their circuit board is damaged or some wires are loosed.
The speaker could also make buzzing noise if the speaker is exposed to some droplets of water.
Electromagnetic waves from other nearby electronics could also be the cause for the buzzing sound so make sure to turn off other devices that may cause it to make some buzzing sound.

How To Factory Reset Your Anker Soundcore 2 Speaker

Follow the steps below to factory reset your Anker Soundcore 2 Speaker:

Click on the PLAY and VOLUME + buttons at the same time

METHOD ONE
  • Press and hold the the VOLUME + and the BLUETOOTH buttons at the same time
  • Keep holding them until it turns off
  • Turn the speaker on
  • The speaker has been reset once it turns on and will now return to pairing mode.
METHOD TWO
  • Turn on the speaker
  • Click and hold on PLAY and VOLUME + at the same time
  • Keep holding until the speaker turns off
  • Press the power button to turn on the speaker
  • The device has been reset and has now returned to pairing mode.
METHOD THREE
  • Turn on the speaker
  • Turn off the speaker
  • Keep it off for about 20 seconds
  • Turn the speaker on again

Is PS5 Quieter Vertically or Horizontally?


Why is My Anker Soundcore 2 Speaker Not Connecting To My PC?

Your Anker Soundcore 2 Speaker is not connecting to your PC either because the option of your Bluetooth had not been switched on.

CHECK OUT:  WiFi Air Conditioner - How To Control Your New or Old AC With WiFi

Follow the steps below to fix the issue:

  • Navigate your way to START
  • Press on Settings Options
  • Choose Bluetooth and other device and turn it on
  • Press the plus button at the top
  • Switch on your Anker Soundcore 2 Speaker
  • Press the Bluetooth and pair the device

Why Is My Anker Soundcore 2 Speaker Not Connecting To My iPhone and How Do I Fix It?

Your Anker Soundcore 2 Speaker is not connecting to your iPhone because of interference from other electronic devices. These devices are bound to cause some electromagnetic waves interference once they are in proximity with your speaker.

Follow the steps below to fix this issue:

  • Switch off every electronic devices that are close by
  • Do it individually so as to fish out the particular device that is causing the interference then switch it off.

Nevertheless, if your iPhone installations are not up-to-date, there is likely to be some issues so check your iPhone to be sure it is up-to-date or get it updated.

After doing all these and it still doesn’t connect then consider turning off your phone and waiting for at least 20 to 30 seconds the. Switch it on again and it will be connected.

If the issue still persists after all these then turn the speaker off and turn it on again then connect the speaker and your iphone.it should work now.

Why is My Anker Soundcore 2 Speaker Not Connecting With Samsung Galaxy Phone?

Your Anker Soundcore 2 Speaker is not connecting with Samsung Galaxy Phone because the speaker and the phone are not in close range and like we said earlier, the bluetooth has range and once the device aiming to connect to the Bluetooth is out of this range then there is bound to be an issue. It could be a low battery problem so while checking for possible issues, try checking for the life of the battery as well and make sure your Bluetooth is turned on.

Follow the steps below to fix this:

  • Shift the phone and the speaker closer to each other
  • Try connecting the both devices
  • Make sure the Bluetooth of the phone is on and if it doesn’t want to toggle on try restarting your phone a d try again.

It should be working now.

Note: always try to update your phone on time as this will save you some unnecessary stress while availing you with good user experience.

Leave a Comment

Your email address will not be published.